Page 1 of 2

Error Message: "CsPro Application has stopped working"

Posted: December 2nd, 2013, 12:46 am
by collinsod
Hi Team, I was working on an application in CsPro that suddenly stopped working and closed.

There after whenever I try to open it, I get this error message "CsPro Application has stopped working. A problem caused the program to stop working correctly. Windows will close the program and notify you if a solution is available " .

Any advice on how to fix this problem will be highly appreciated.

Collinsod

Re: Error Message: "CsPro Application has stopped working"

Posted: December 5th, 2013, 6:46 am
by khurshid.arshad
Dear collinsod

I have go through your program and you have create three items under IDS0. My suggestion is Sdate and Name_Enmerator to move under personal_info. It will be difficult to put Questionnaire+Sdate+Name_Enumerator when you try to find out questionnaire ID during the data entry in CSPro
a.

Re: Error Message: "CsPro Application has stopped working"

Posted: November 29th, 2016, 11:28 pm
by franckkoutepe
Hi

I have the same problem. Can you help me please ?
Franck

Re: Error Message: "CsPro Application has stopped working"

Posted: November 30th, 2016, 3:31 am
by khurshid.arshad
Dear Franckkoutepe
The error was in your page 7 and now it is fixed.

In form design Q5_3, Q5_8 and Q5_8_BIS shown multi occurance but in dictionary has only "1" occ.

a.

Re: Error Message: "CsPro Application has stopped working"

Posted: November 30th, 2016, 11:55 am
by franckkoutepe
Thank You very much Arsahd

Re: Error Message: "CsPro Application has stopped working"

Posted: December 5th, 2016, 5:33 am
by joemetjose
Hi..

I also face the same problem. It would be nice if you can have look at it.

Re: Error Message: "CsPro Application has stopped working"

Posted: December 5th, 2016, 7:44 am
by khurshid.arshad
Dear Joemetjose

Can you explain that on which form you are facing problem.

I have done some entry but it is working fine.

a.

Re: Error Message: "CsPro Application has stopped working"

Posted: December 5th, 2016, 9:50 am
by joemetjose
Dear Arshad,

There is no specific problem with any form. My operators are able to enter the data for some cases. But in between it crashes. It can be in any form, So i am unable to find out whats causing the problem. There are two kinds of problems i am encountering. One is "CSPro Application has stopped working" error. Another one is I get a message box that "the required resource" then an option to click ok. The message is not full. Has it something to do with video card or something. However, in this case I am able to partially save and close the application and come back to the exact position where I stopped. Also sometimes the screen becomes blank. It only shows field boxes in disabled form. Means you can see the fields but cant do anything. These are all systems with 2gb ram and windows 7. I have not checked the processor.

Re: Error Message: "CsPro Application has stopped working"

Posted: December 6th, 2016, 1:35 am
by joemetjose
Sorry the exact message I am getting is 'data entry has stopped working'. Please see the attachment.

Re: Error Message: "CsPro Application has stopped working"

Posted: February 4th, 2018, 11:51 pm
by hannesrr
Hello there,

Regards from PerĂº.

Do you have any solution about this issue?, because my users frecuently reports this error message.
Please If you have any advice, share with us,

Regards

Hannes.